HIGHLIGHTS
Over 15 years of extensive experience as Process Engineer in providing the front-end process/system design, review and technical support to procurement, installation, commissioning, start-up and operation for chemical projects. Over 5 years of experience as Process Engineer in providing process calculation and P&ID design of pressure relief system and flare system for chemical, petrochemical and refinery projects in USA & Canada
Good knowledge of Codes, Standards and Regulations such as: ASME Code section I/VIII, NB-18, API RP 520/521/2000 Standards and Crane TP410
Good command of software MS-Office, AUTOCAD, STX, iPRSM, FLARENET, HYSYS and etc.
PROFESSIONAL EXPERIENCE
PROFESSIONAL EXPERIENCE
March-May, 2011 Process Engineer SNC-Lavalin inc., Sarnia, Ontario, Canada
*Worked on the Relief and Flare System of the Debottlenecking project which consists of twelve ISBL Process units and ten off-sites and utilities systems. Duties included the sizing/rating of PSV flows, PSVs inlet and outlet pipes pressure drops calculations and system mitigation, even for those very complicated systems such as distillation system, reactor loop, two-phase flow calculations, fire critical mode etc for North Atlantic Refinery Debottlenecking Project, Come-By-Chance, Newfoundland, Canada (The project is on hold now)
Sept-Dec, 2010 Process Engineer Diacreek Engineering Inc., Toronto, Canada
*Worked process/piping design for utility system for water treatment system and oil &gas project development
June 2006-Sept 2009 Process Engineer Farris Engineering, Curtiss Wright Flow Control Company, Branford, Ontario, Canada
Responsible for analyzing, calculating and mitigating Pressure Relief Systems per ASME section I/III/VIII codes, API 520/521/2000 standards for chemical, petrochemical and refinery projects. Nearly 500 pressure relief systems were successfully completed. The following projects were included:
*Valero Refining Company, Louisiana, USA (2008-2009)
*Koch Fertilizer Plant, Brandon, Manitoba, Canada (2008-2009)
*Husky Lima Refinery, Ohio, USA (2007-2008)
*DSM Nutritional Products, Inc., Freeport, USA (2007-2008)
*Bruce Power, Tiverton, CA (2006-2007)
Duties included:
*Analyzed process/system documents such as: Process Flow Diagrams (PFDs), material & heat balances, Piping & Instrument Diagrams (P&IDs), operating & maintenance manuals, manufacturer catalogues, drawings, equipment data sheets, operating parameters and etc
*Identified pressure relief system protected scope, potential hazards and overpressure factors
*Calculated required relieving loads and pipe loss of pressure relief devices per ASME codes and API standards as well as DIERS methodology
*Prepared system mitigation and technical specification
Oct. 2002-Dec. 2004 Lead Process Engineer Maison Worley Parsons, shanghai, China
Responsible for basic process design, detail design review and technical support to procurement, installation, start-up, operation and maintenance for food revamping project and chemical Project
Duties included:
*Performed bottleneck identification, process assessment, process optimum and process selection for existing manufacturing facility
*Provided project feasibility study report regarding to technical comparison, selection and cost estimation
*Preformed basic engineering design such as preparing PFDs, P&IDs, sizing control valves and safety valves, preparing technical specifications of product cooler, evaporation system and pump system and reviewing vendor¡¯s drawings, etc.
*Performed detail engineering design review
¡ñWorked as an interface with procurement manager, construction manager, production manager, quality manager, plant manager and vendors
*Prepared bid invitation document, evaluated technical proposal and commercial proposal and recommended qualified vendors
*Participated in start-up, shut-down, operation and maintenance
1987-Oct. 2002 Process Engineer China Wuhuan Chemical Engineering Corporation
Responsible for the front-end process & system design on technical proposal, feasibility study report, concept design, basic engineering design, detail engineering design, procurement support, field installation, commissioning, start-up and performance guarantee test of urea and ammonia plants. The main projects that I completed included:
*60m3/hr Waste Water Treatment Project, Panjin Petrochemical Plant, C...
Login or Register to view the full resume.
